---
type: "fit-size"
designation: "f7"
nominal_size_mm: 100
feature: "shaft"
letter: "f"
it_grade: "ITIT7"
upper_deviation_um: -36
lower_deviation_um: -71
min_dia_mm: 99.929
max_dia_mm: 99.964
it_tolerance_um: 35
standard: "ISO 286-1:2010, ISO 286-2:2010"
verified: "August 1, 2026"
url: https://shopmath.org/fits/f7/100mm
---

# 100 mm f7 Tolerance — Limits, Deviations and Band

A 100 mm f7 shaft runs 99.929 to 99.964 mm — deviations -71 to -36 µm from nominal, on an ITIT7 band of 35 µm. Close running shaft — the standard choice for lubricated journals at moderate speed.

- **Designation**: f7 at 100 mm
- **Feature**: shaft
- **Upper limit**: 99.964 mm (-36 µm)
- **Lower limit**: 99.929 mm (-71 µm)
- **Tolerance band**: 35 µm (ITIT7)
- **Fundamental deviation**: f — Close running clearance
- **Standard**: ISO 286-1:2010, ISO 286-2:2010

## 100 mm f7 Limits

| Property | Micrometres | Millimetres |
| --- | --- | --- |
| Upper deviation | -36 | -0.036 |
| Lower deviation | -71 | -0.071 |
| Tolerance band (IT) | 35 | 0.035 |
| Maximum diameter |  | 99.964 |
| Minimum diameter |  | 99.929 |

_Deviations are measured from the nominal size. A diameter outside the two limits is a reject._

## Other Standard Tolerances at 100 mm

The other ISO 286 designations that carry a page at 100 mm — the comparison to make when f7 is the wrong fit.

| Designation | Feature | Lower deviation (µm) | Upper deviation (µm) | Min Ø (mm) | Max Ø (mm) | IT band (µm) |
| --- | --- | --- | --- | --- | --- | --- |
| [g6](https://shopmath.org/fits/g6/100mm.md) | shaft | -34 | -12 | 99.966 | 99.988 | 22 |
| [h6](https://shopmath.org/fits/h6/100mm.md) | shaft | -22 | +0 | 99.978 | 100.000 | 22 |
| [H7](https://shopmath.org/fits/h7/100mm.md) | hole | +0 | +35 | 100.000 | 100.035 | 35 |
| [h7](https://shopmath.org/fits/h7-shaft/100mm.md) | shaft | -35 | +0 | 99.965 | 100.000 | 35 |
| [p6](https://shopmath.org/fits/p6/100mm.md) | shaft | +37 | +59 | 100.037 | 100.059 | 22 |

## ISO 286 Standard Tolerance Grades at 100 mm

Every IT grade in the size band 100 mm falls in. The letter sets where the band sits; the IT grade sets how wide it is.

| Grade | Tolerance (µm) | Tolerance (mm) |
| --- | --- | --- |
| IT5 | 15 | 0.015 |
| IT6 | 22 | 0.022 |
| IT7 | 35 | 0.035 |
| IT8 | 54 | 0.054 |
| IT9 | 87 | 0.087 |
| IT10 | 140 | 0.140 |
| IT11 | 220 | 0.220 |
| IT12 | 350 | 0.350 |

## Sources and Method for 100 mm f7

### f7 at 100 mm

- **Source**: limits computed from the compiled ISO 286 tables: ISO 286-1 IT grades and ISO 286-2 fundamental deviations, compiled from saucecode/ISO286 (LGPL-2.1) and parkergreene/isofits (MIT), cross-checked cell-for-cell
- **Method**: computed
- **Verified against**: parkergreene/isofits ISO 286-2 limit tables (MIT); ISO 286-1 formula harness — 2067 checks passed

### Assumptions

- Values are the ISO 286-2 tabulated limits, not the ISO 286-1 formula: the formula deviates from the table by up to 13.26% and is carried only as a validation harness.
- Limits are at 20 °C, the ISO 1 reference temperature.
- ISO 286 tabulates per size band, so this value holds across the band the nominal size falls in.
- Dataset scope: COMPILED not computed: the ISO 286-1 formula deviates up to 13.26% from the table and is used only as a harness (warn >5%, fail >15%). EXCLUDED: shaft/hole letters s, t, u and the fits H7/s6, H7/t6, H7/u6 — no free source and an undetermined step constant in the formula.

**Data last verified**: August 1, 2026

## Common Questions About 100 mm f7

### What is the tolerance for a 100 mm f7 shaft?

A 100 mm f7 shaft is 99.929 to 99.964 mm — deviations -71 to -36 µm from nominal, a total tolerance band of 35 µm.

### What size reamer or bore does a 100 mm f7 shaft need?

Aim for the middle of the band: 99.947 mm, with 35 µm of total spread available between 99.929 and 99.964 mm.

### How much is 35 µm in millimetres and inches?

35 µm is 0.035 mm, or 0.00138 in.

## Related pages

- Smaller size: [80 mm f7](https://shopmath.org/fits/f7/80mm.md)
- All sizes of this tolerance: [f7 limits by size](https://shopmath.org/fits/f7.md)
- All fits and tolerances: [ISO 286 fit reference](https://shopmath.org/fits.md)
- Full grade table: [ISO 286 tolerance chart](https://shopmath.org/charts/iso-tolerances.md)

---

*Source: [ShopMath](https://shopmath.org/fits/f7/100mm) — data verified August 1, 2026. Reference data; verify against the governing standard before manufacture.*