---
type: "thread"
name: "7/16\"-28 UNEF"
designation: "7/16-28 UNEF"
series: "unef"
series_name: "Unified Extra Fine (UNEF)"
system: "unified"
size_label: "7/16"
tpi: 28
pitch_in: 0.035714
pitch_mm: 0.9071
basic_major_dia_in: 0.4375
basic_major_dia_mm: 11.1125
basic_pitch_dia_in: 0.4143
basic_pitch_dia_mm: 10.5232
basic_minor_dia_in: 0.3988
basic_minor_dia_mm: 10.1295
tap_drill: "Y"
tap_drill_dia_in: 0.404
tap_drill_dia_mm: 10.2616
tap_drill_thread_pct: 72.2
clearance_normal_drill: "29/64"
tensile_stress_area_sqin: 0.127368
tensile_stress_area_sqmm: 82.173
internal_class_assumed: "2B"
standard: "ASME B1.1 (reference values based on the ASME B1.1 system; not a compliance claim)"
verified: "August 1, 2026"
url: https://shopmath.org/threads/unef/7-16-28
---

# 7/16"-28 UNEF Thread — Dimensions, Tap Drill & Clearance

The tap drill for 7/16"-28 UNEF is Y — 0.4040 in (10.262 mm) — which leaves 72.2% thread engagement with a cut tap. Basic pitch diameter is 0.4143 in (10.523 mm) and basic minor diameter is 0.3988 in (10.130 mm). Tapped-hole figures on this page assume a class 2B thread; drill sizes for 50–85% engagement are in the tap drill table below.

- **Series**: Unified Extra Fine (UNEF)
- **Designation**: 7/16-28 UNEF
- **Threads per inch**: 28
- **Tap drill**: Y
- **Standard**: ASME B1.1 (reference values based on the ASME B1.1 system; not a compliance claim)

## Basic Thread Dimensions for 7/16"-28 UNEF

| Property | Inch | Millimetre |
| --- | --- | --- |
| Basic major diameter | 0.4375 | 11.113 |
| Threads per inch | 28 | — |
| Pitch | 0.0357 | 0.907 |
| Basic pitch diameter | 0.4143 | 10.523 |
| Basic minor diameter | 0.3988 | 10.130 |
| External thread root diameter | 0.3950 | 10.033 |
| Sharp V thread height (H) | 0.0309 | 0.785 |

_Basic dimensions are the theoretical values before any tolerance class is applied._

## Tap Drill Sizes for 7/16"-28 UNEF

Cut taps, from 50% to 85% thread engagement. The shop default is 75% — a Y drill.

| Thread % | Target hole Ø (in) | Target hole Ø (mm) | Drill | Drill Ø (in) | Drill Ø (mm) | Actual thread % |
| --- | --- | --- | --- | --- | --- | --- |
| 50% | 0.4143 | 10.523 | Z | 0.4130 | 10.490 | 52.8 |
| 60% | 0.4097 | 10.406 | Z | 0.4130 | 10.490 | 52.8 |
| 65% | 0.4073 | 10.345 | 13/32 | 0.4063 | 10.319 | 67.4 |
| 70% | 0.4050 | 10.287 | Y | 0.4040 | 10.262 | 72.2 |
| 75% (default) | 0.4027 | 10.229 | Y | 0.4040 | 10.262 | 72.2 |
| 80% | 0.4004 | 10.170 | X | 0.3970 | 10.084 | 87.3 |
| 85% | 0.3981 | 10.112 | X | 0.3970 | 10.084 | 87.3 |

_Target hole Ø is the theoretical hole for the stated engagement. The drill column is the nearest size in the standard number/letter/fractional/metric index, and actual thread % is what that real drill produces._

## Clearance Hole Sizes for 7/16"-28 UNEF

The through-hole a 7/16"-28 UNEF fastener passes freely, not the tapped hole.

| Fit | Drill | Hole Ø (in) | Hole Ø (mm) | Use |
| --- | --- | --- | --- | --- |
| Close | 7/16 | 0.4528 | 11.501 | Located joints, dowelled assemblies |
| Normal | 29/64 | 0.4685 | 11.900 | General assembly — the default |
| Loose | 15/32 | 0.4843 | 12.301 | Slotted or adjustable joints, weldments |

_Clearance holes per ISO 273 (metric) and ASME B18.2.8 (inch)._

## Thread Class Limits for 7/16"-28 UNEF

Manufacturing limits for classes 2B, 3B, 2A, 3A. A gauge reading outside these bands is a reject, not a judgement call.

### External thread (bolt / screw) limits

| Limit | Class 2A (in) | Class 2A (mm) | Class 3A (in) | Class 3A (mm) |
| --- | --- | --- | --- | --- |
| Major Ø max | 0.4364 | 11.085 | 0.4375 | 11.113 |
| Major Ø min | 0.4299 | 10.919 | 0.4310 | 10.947 |
| Pitch Ø max | 0.4132 | 10.495 | 0.4143 | 10.523 |
| Pitch Ø min | 0.4096 | 10.404 | 0.4116 | 10.455 |
| Pitch Ø tolerance | 0.0036 | 0.091 | 0.0027 | 0.069 |
| Minor Ø max | 0.3900 | 9.906 | 0.3911 | 9.934 |
| Minor Ø min | 0.3864 | 9.815 | 0.3884 | 9.865 |
| Allowance | 0.0011 | 0.028 | 0.0000 | 0.000 |

### Internal thread (nut / tapped hole) limits

| Limit | Class 2B (in) | Class 2B (mm) | Class 3B (in) | Class 3B (mm) |
| --- | --- | --- | --- | --- |
| Major Ø max | 0.4474 | 11.364 | 0.4462 | 11.334 |
| Major Ø min | 0.4375 | 11.113 | 0.4375 | 11.113 |
| Pitch Ø max | 0.4190 | 10.643 | 0.4178 | 10.612 |
| Pitch Ø min | 0.4143 | 10.523 | 0.4143 | 10.523 |
| Pitch Ø tolerance | 0.0047 | 0.119 | 0.0035 | 0.089 |
| Minor Ø max | 0.4073 | 10.345 | 0.4051 | 10.290 |
| Minor Ø min | 0.3988 | 10.130 | 0.3988 | 10.130 |
| Allowance | 0.0000 | 0.000 | 0.0000 | 0.000 |

## Tensile Stress Area of 7/16"-28 UNEF

| Property | in² | mm² |
| --- | --- | --- |
| Tensile stress area | 0.12737 | 82.17 |

The effective cross-section used to size a 7/16"-28 UNEF fastener against a load. Multiply it by the material's allowable stress — the area itself carries no strength assumption.

## Other Thread Pitches in the Same Size as 7/16"-28 UNEF

A 7/16 fastener is not always 7/16"-28 UNEF. These are the other standard pitches cut on the same nominal size.

| Thread | Series | Pitch | Tap drill |
| --- | --- | --- | --- |
| [7/16"-20 UNF](https://shopmath.org/threads/unf/7-16-20.md) | Unified Fine (UNF) | 20 TPI | 25/64 |
| [7/16"-14 UNC](https://shopmath.org/threads/unc/7-16-14.md) | Unified Coarse (UNC) | 14 TPI | U |

## Sources and Method for 7/16"-28 UNEF

### Basic dimensions

- **Source**: NBS Handbook H28 (1969) Part I §§6-7 (public domain, 17 U.S.C. 105); normative modern reference ASME B1.1; series membership: Series membership: threadlib UIS_thread.csv (BSD-3-Clause); cross-checked against NBS H28 (1969) Part I Table 2.21; clearance holes: ISO 273 (metric) and ASME B18.2.8 (inch) via FreeCAD FeatureHole.cpp (LGPL-2.1+), cross-checked against bd_warehouse clearance_hole_sizes.csv (Apache-2.0)
- **Method**: computed
- **Verified against**: NBS H28 (1969) Part I, Table 2.21 (public domain); cross-checked against FreeCAD CAM thread tables (LGPL-2.1+) — 1064 checks passed at 0.0001 in

### Tap drill sizes

- **Source**: Machinery's Handbook %-thread formula (geometry-derived); nearest-standard-drill-to-75% rule verified at 36/39 published chart rows in docs/research/data-sourcing.md §3.4
- **Method**: computed
- **Verified against**: Wikipedia Unified Thread Standard, preferred cutting tap drill size columns (CC BY-SA 4.0) — 36/39 published UNC+UNF rows reproduced

### Class limits

- **Source**: NBS Handbook H28 (1969) Part I §§6-7 (public domain, 17 U.S.C. 105); normative modern reference ASME B1.1
- **Method**: computed
- **Verified against**: NBS H28 (1969) Part I, Table 2.21 (public domain); cross-checked against FreeCAD CAM thread tables (LGPL-2.1+) — 1064 checks passed at 0.0001 in

### Formulas

**Tap drill hole diameter, inch threads**

```text
hole Ø  =  D − (%thread ÷ 100) × (1.29904 ÷ n)

  D = basic major diameter (in)
  n = threads per inch
```

_1.29904 = 2 × 0.64952, twice the engaged thread height per side on the 60° Unified profile._

**Actual thread engagement of the chosen drill**

```text
%thread  =  (D − drill Ø) × n ÷ 1.29904 × 100
```

_The drill column rounds to a real drill; this is the engagement that drill actually leaves._

**Tensile stress area, Unified inch threads**

```text
At  =  0.7854 × (D − 0.9743 ÷ n)²
```

_ASME B1.1 / NBS H28 form. Reproduces the stored value exactly for this thread._

### Assumptions

- The headline tap drill assumes 75% thread engagement, the general shop default. Every engagement from 50% to 85% is in the tap drill table — change the assumption and the number moves.
- Tap drill figures are for cut taps. Drill diameters are nominal; a worn or run-out drill cuts oversize and reduces engagement further.
- Tapped-hole figures assume a class 2B internal thread, the general-purpose fit.
- Dataset scope: Le = 1D for UNC/UNF, 9P for UNEF — determined empirically against H28 Table 2.21, resolving data-sourcing.md open item 5. EXCLUDED: form (roll) tap drills, class 1A/1B limits, class 1AR allowances, constant-pitch UN series.

**Data last verified**: August 1, 2026

## Common Questions About 7/16"-28 UNEF

### What is the tap drill size for 7/16"-28 UNEF?

The tap drill for 7/16"-28 UNEF is Y — 0.4040 in (10.262 mm). That leaves 72.2% thread engagement with a cut tap.

### What is the pitch diameter of 7/16"-28 UNEF?

The basic pitch diameter of 7/16"-28 UNEF is 0.4143 in (10.523 mm). For a class 2B thread it runs 0.4143 in (10.523 mm) to 0.4190 in (10.643 mm).

### What is the minor diameter of 7/16"-28 UNEF?

The basic minor diameter of 7/16"-28 UNEF is 0.3988 in (10.130 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.

### What is the thread pitch of 7/16"-28 UNEF?

7/16"-28 UNEF has 28 threads per inch, a pitch of 0.0357 in (0.907 mm).

### What size clearance hole does a 7/16"-28 UNEF fastener need?

close fit 7/16 (0.4528 in (11.501 mm)), normal fit 29/64 (0.4685 in (11.900 mm)), loose fit 15/32 (0.4843 in (12.301 mm)). The normal fit is the general-assembly default.

### What is the tensile stress area of 7/16"-28 UNEF?

The tensile stress area of 7/16"-28 UNEF is 0.12737 in² (82.17 mm²). Multiply it by the fastener material's allowable stress to get a load.

## Related pages

- Smaller in Unified Extra Fine (UNEF): [3/8"-32 UNEF](https://shopmath.org/threads/unef/3-8-32.md) — tap drill 11/32
- Larger in Unified Extra Fine (UNEF): [1/2"-28 UNEF](https://shopmath.org/threads/unef/1-2-28.md) — tap drill 15/32
- All Unified Extra Fine (UNEF) sizes: [Unified Extra Fine (UNEF) thread chart](https://shopmath.org/threads/unef.md)
- Every thread series: [Screw thread reference](https://shopmath.org/threads.md)
- Cross-series chart: [Tap drill chart](https://shopmath.org/charts/tap-drill.md)

---

*Source: [ShopMath](https://shopmath.org/threads/unef/7-16-28) — data verified August 1, 2026. Reference data; verify against the governing standard before manufacture.*