What is the tap drill size for 1 1/2-11.5 NPT?

The tap drill for 1 1/2-11.5 NPT is 1 — 1.0000 in (25.400 mm). Taper pipe threads are tapped with a taper tap and sealed with compound or tape.

What is the pitch diameter of 1 1/2-11.5 NPT?

The basic pitch diameter of 1 1/2-11.5 NPT is 1.8223 in (46.287 mm).

What is the minor diameter of 1 1/2-11.5 NPT?

The basic minor diameter of 1 1/2-11.5 NPT is 1.7528 in (44.521 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.

What is the thread pitch of 1 1/2-11.5 NPT?

1 1/2-11.5 NPT has 12 threads per inch, a pitch of 0.0870 in (2.209 mm).

What is the hand-tight engagement length (L₁) of 1 1/2-11.5 NPT?

The hand-tight engagement length L₁ for 1 1/2-11.5 NPT is 0.4200 in (10.668 mm), on a pipe outside diameter of 1.9000 in (48.260 mm).

NPT Taper Pipe Thread · 1 1/2-11.5 NPT

1 1/2-11.5 NPT Thread — Dimensions, Tap Drill & Clearance

https://shopmath.org/threads/npt/1-1-2 · data verified August 1, 2026

The tap drill for 1 1/2-11.5 NPT taper pipe thread is 1 — 1.0000 in (25.400 mm). Basic pitch diameter is 1.8223 in (46.287 mm) and basic minor diameter is 1.7528 in (44.521 mm).

Series: NPT Taper Pipe Thread
Designation: 1 1/2-11.5 NPT
TPI: 12
Standard: ASME B1.20.1, ASME B1.20.3; public-domain primary FED-STD-H28/7A

Tap drill · taper pipe tap

Drill Ø: 1.0000in
Drill Ø: 25.400mm

NPT and NPTF holes are drilled straight and cut with a taper tap. The standard assumes a sealing compound or tape on the joint.

Basic Thread Dimensions for 1 1/2-11.5 NPT

Basic thread dimensions — 1 1/2-11.5 NPT
Property	Inch	Millimetre
Basic major diameter	1.9000	48.260
Threads per inch	12	—
Pitch	0.0870	2.209
Basic pitch diameter	1.8223	46.287
Basic minor diameter	1.7528	44.521
Sharp V thread height (H)	0.0753	1.913

Threads per inch has no millimetre counterpart — metric threads are specified by pitch instead. Basic dimensions are the theoretical values before any tolerance class is applied.

Taper Pipe Thread Geometry for 1 1/2-11.5 NPT

1 1/2-11.5 NPT is a taper thread: the diameter changes along the thread, so every diameter below is stated at a named plane. The taper is 0.7500 in per foot on diameter.

Taper pipe thread geometry — 1 1/2-11.5 NPT
Property	Inch	Millimetre
Pipe outside diameter	1.9000	48.260
Taper on diameter, per foot	0.7500	19.050
Pitch Ø at end of pipe (E₀)	1.7961	45.621
Pitch Ø at hand-tight plane (E₁)	1.8223	46.287
Pitch Ø at effective plane (E₂)	1.8413	46.769
Hand-tight engagement (L₁)	0.4200	10.668
Effective thread length (L₂)	0.7235	18.377
Overall external thread length (L₄)	1.0252	26.040
Thread height (h)	0.0696	1.767
Sharp V height (H)	0.0753	1.913
Minor Ø at hand-tight plane	1.7528	44.521

ASME B1.20.1 publishes these dimensions in inches only; the millimetre column is an exact conversion (1 in = 25.4 mm by definition). L₁ is the hand-tight engagement length and is tabulated in the standard, not derived.

Other Thread Pitches in the Same Size as 1 1/2-11.5 NPT

A 1 1/2 fastener is not always 1 1/2-11.5 NPT. These are the other standard pitches cut on the same nominal size.

Other standard pitches at nominal size 1 1/2
Thread	Series	Pitch	Tap drill
1 1/2-11.5 NPTF	NPTF Dryseal Pipe Thread	12 TPI	1

Sources and Method for 1 1/2-11.5 NPT

Basic dimensions · Taper pipe geometrycomputed+compiled

ASME B1.20.1 taper pipe thread formulas; E0 and L2 reproduced to 5 decimals in docs/research/data-sourcing.md §3.3. Public-domain primary: FED-STD-H28/7A (1984).; pipe OD / tpi / L1 / L4: ASME B1.20.1 pipe OD / tpi / L1 / L4 via Wikipedia National pipe thread (CC BY-SA 4.0); OD and tpi cross-checked against FreeCAD FeatureHole.cpp NPT block (LGPL-2.1+)

Verified against Wikipedia National pipe thread standard-sizes table (CC BY-SA 4.0) — 98 checks passed to 1e-5 in

Part computed from the standard's formulas, part compiled from agreeing public sources.

Assumptions

NPT threads are not a seal on their own — the standard assumes a sealing compound or tape on the joint.
Dataset scope: L1 is tabulated, not derivable (data-sourcing.md §3.3). EXCLUDED: NPTF crest/root truncation limits (single-sourced), NPSM/NPSC/NPSF straight pipe threads, BSPT/BSPP.

Data last verified

August 1, 2026

How this data is built and checked →

How to Cite This 1 1/2-11.5 NPT Reference

Citation

ShopMath. "1 1/2-11.5 NPT Thread — Dimensions, Tap Drill & Clearance." ShopMath, verified August 1, 2026, https://shopmath.org/threads/npt/1-1-2

BibTeX

@misc{shopmath-threads-npt-1-1-2,
  title        = {1 1/2-11.5 NPT Thread — Dimensions, Tap Drill & Clearance},
  author       = {{ShopMath}},
  year         = {2026},
  howpublished = {\url{https://shopmath.org/threads/npt/1-1-2}},
  note         = {Data verified 2026-08-01}
}

Permanent URL

https://shopmath.org/threads/npt/1-1-2

Common Questions About 1 1/2-11.5 NPT

What is the tap drill size for 1 1/2-11.5 NPT?: The tap drill for 1 1/2-11.5 NPT is 1 — 1.0000 in (25.400 mm). Taper pipe threads are tapped with a taper tap and sealed with compound or tape.
What is the pitch diameter of 1 1/2-11.5 NPT?: The basic pitch diameter of 1 1/2-11.5 NPT is 1.8223 in (46.287 mm).
What is the minor diameter of 1 1/2-11.5 NPT?: The basic minor diameter of 1 1/2-11.5 NPT is 1.7528 in (44.521 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.
What is the thread pitch of 1 1/2-11.5 NPT?: 1 1/2-11.5 NPT has 12 threads per inch, a pitch of 0.0870 in (2.209 mm).
What is the hand-tight engagement length (L₁) of 1 1/2-11.5 NPT?: The hand-tight engagement length L₁ for 1 1/2-11.5 NPT is 0.4200 in (10.668 mm), on a pipe outside diameter of 1.9000 in (48.260 mm).

All NPT Taper Pipe Thread sizes · Every thread series