What is the tap drill size for 1-11.5 NPTF?

The tap drill for 1-11.5 NPTF is 1 — 1.0000 in (25.400 mm). Taper pipe threads are tapped with a taper tap and sealed with compound or tape.

What is the pitch diameter of 1-11.5 NPTF?

The basic pitch diameter of 1-11.5 NPTF is 1.2386 in (31.461 mm).

What is the minor diameter of 1-11.5 NPTF?

The basic minor diameter of 1-11.5 NPTF is 1.1691 in (29.695 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.

What is the thread pitch of 1-11.5 NPTF?

1-11.5 NPTF has 12 threads per inch, a pitch of 0.0870 in (2.209 mm).

What is the hand-tight engagement length (L₁) of 1-11.5 NPTF?

The hand-tight engagement length L₁ for 1-11.5 NPTF is 0.4000 in (10.160 mm), on a pipe outside diameter of 1.3150 in (33.401 mm).

NPTF Dryseal Pipe Thread · 1-11.5 NPTF

1-11.5 NPTF Thread — Dimensions, Tap Drill & Clearance

https://shopmath.org/threads/nptf/1 · data verified August 1, 2026

The tap drill for 1-11.5 NPTF taper pipe thread is 1 — 1.0000 in (25.400 mm). Basic pitch diameter is 1.2386 in (31.461 mm) and basic minor diameter is 1.1691 in (29.695 mm).

Series: NPTF Dryseal Pipe Thread
Designation: 1-11.5 NPTF
TPI: 12
Standard: ASME B1.20.1, ASME B1.20.3; public-domain primary FED-STD-H28/7A

Tap drill · taper pipe tap

Drill Ø: 1.0000in
Drill Ø: 25.400mm

NPT and NPTF holes are drilled straight and cut with a taper tap. The standard assumes a sealing compound or tape on the joint.

Basic Thread Dimensions for 1-11.5 NPTF

Basic thread dimensions — 1-11.5 NPTF
Property	Inch	Millimetre
Basic major diameter	1.3150	33.401
Threads per inch	12	—
Pitch	0.0870	2.209
Basic pitch diameter	1.2386	31.461
Basic minor diameter	1.1691	29.695
Sharp V thread height (H)	0.0753	1.913

Threads per inch has no millimetre counterpart — metric threads are specified by pitch instead. Basic dimensions are the theoretical values before any tolerance class is applied.

Taper Pipe Thread Geometry for 1-11.5 NPTF

1-11.5 NPTF is a taper thread: the diameter changes along the thread, so every diameter below is stated at a named plane. The taper is 0.7500 in per foot on diameter.

Taper pipe thread geometry — 1-11.5 NPTF
Property	Inch	Millimetre
Pipe outside diameter	1.3150	33.401
Taper on diameter, per foot	0.7500	19.050
Pitch Ø at end of pipe (E₀)	1.2136	30.826
Pitch Ø at hand-tight plane (E₁)	1.2386	31.461
Pitch Ø at effective plane (E₂)	1.2563	31.910
Hand-tight engagement (L₁)	0.4000	10.160
Effective thread length (L₂)	0.6828	17.343
Overall external thread length (L₄)	0.9845	25.006
Thread height (h)	0.0696	1.767
Sharp V height (H)	0.0753	1.913
Minor Ø at hand-tight plane	1.1691	29.695

ASME B1.20.1 publishes these dimensions in inches only; the millimetre column is an exact conversion (1 in = 25.4 mm by definition). L₁ is the hand-tight engagement length and is tabulated in the standard, not derived.

Other Thread Pitches in the Same Size as 1-11.5 NPTF

A 1 fastener is not always 1-11.5 NPTF. These are the other standard pitches cut on the same nominal size.

Other standard pitches at nominal size 1
Thread	Series	Pitch	Tap drill
1-11.5 NPT	NPT Taper Pipe Thread	12 TPI	1

Sources and Method for 1-11.5 NPTF

Basic dimensionscomputed+compiled

ASME B1.20.1 taper pipe thread formulas; E0 and L2 reproduced to 5 decimals in docs/research/data-sourcing.md §3.3. Public-domain primary: FED-STD-H28/7A (1984).; pipe OD / tpi / L1 / L4: ASME B1.20.1 pipe OD / tpi / L1 / L4 via Wikipedia National pipe thread (CC BY-SA 4.0); OD and tpi cross-checked against FreeCAD FeatureHole.cpp NPT block (LGPL-2.1+). NPTF shares the NPT taper geometry; dryseal crest/root truncation limits are NOT included (single-source only — see generator header).

Verified against Wikipedia National pipe thread standard-sizes table (CC BY-SA 4.0) — 98 checks passed to 1e-5 in

Part computed from the standard's formulas, part compiled from agreeing public sources.

Taper pipe geometrycomputed+compiled

Verified against Wikipedia National pipe thread standard-sizes table (CC BY-SA 4.0) — 98 checks passed to 1e-5 in

Part computed from the standard's formulas, part compiled from agreeing public sources.

Assumptions

NPT threads are not a seal on their own — the standard assumes a sealing compound or tape on the joint.
Dataset scope: L1 is tabulated, not derivable (data-sourcing.md §3.3). EXCLUDED: NPTF crest/root truncation limits (single-sourced), NPSM/NPSC/NPSF straight pipe threads, BSPT/BSPP.

Data last verified

August 1, 2026

How this data is built and checked →

How to Cite This 1-11.5 NPTF Reference

Citation

ShopMath. "1-11.5 NPTF Thread — Dimensions, Tap Drill & Clearance." ShopMath, verified August 1, 2026, https://shopmath.org/threads/nptf/1

BibTeX

@misc{shopmath-threads-nptf-1,
  title        = {1-11.5 NPTF Thread — Dimensions, Tap Drill & Clearance},
  author       = {{ShopMath}},
  year         = {2026},
  howpublished = {\url{https://shopmath.org/threads/nptf/1}},
  note         = {Data verified 2026-08-01}
}

Permanent URL

https://shopmath.org/threads/nptf/1

Common Questions About 1-11.5 NPTF

What is the tap drill size for 1-11.5 NPTF?: The tap drill for 1-11.5 NPTF is 1 — 1.0000 in (25.400 mm). Taper pipe threads are tapped with a taper tap and sealed with compound or tape.
What is the pitch diameter of 1-11.5 NPTF?: The basic pitch diameter of 1-11.5 NPTF is 1.2386 in (31.461 mm).
What is the minor diameter of 1-11.5 NPTF?: The basic minor diameter of 1-11.5 NPTF is 1.1691 in (29.695 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.
What is the thread pitch of 1-11.5 NPTF?: 1-11.5 NPTF has 12 threads per inch, a pitch of 0.0870 in (2.209 mm).
What is the hand-tight engagement length (L₁) of 1-11.5 NPTF?: The hand-tight engagement length L₁ for 1-11.5 NPTF is 0.4000 in (10.160 mm), on a pipe outside diameter of 1.3150 in (33.401 mm).

All NPTF Dryseal Pipe Thread sizes · Every thread series