What is the tap drill size for 11/16"-24 UNEF?

The tap drill for 11/16"-24 UNEF is 41/64 — 0.6406 in (16.272 mm). That leaves 86.6% thread engagement with a cut tap.

What is the pitch diameter of 11/16"-24 UNEF?

The basic pitch diameter of 11/16"-24 UNEF is 0.6604 in (16.774 mm). For a class 2B thread it runs 0.6604 in (16.774 mm) to 0.6657 in (16.909 mm).

What is the minor diameter of 11/16"-24 UNEF?

The basic minor diameter of 11/16"-24 UNEF is 0.6424 in (16.317 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.

What is the thread pitch of 11/16"-24 UNEF?

11/16"-24 UNEF has 24 threads per inch, a pitch of 0.0417 in (1.058 mm).

What is the tensile stress area of 11/16"-24 UNEF?

The tensile stress area of 11/16"-24 UNEF is 0.32868 in² (212.05 mm²). Multiply it by the fastener material's allowable stress to get a load.

Unified Extra Fine (UNEF) · 11/16-24 UNEF

11/16"-24 UNEF Thread — Dimensions, Tap Drill & Clearance

https://shopmath.org/threads/unef/11-16-24 · data verified August 1, 2026

The tap drill for 11/16"-24 UNEF is 41/64 — 0.6406 in (16.272 mm) — which leaves 86.6% thread engagement with a cut tap. Basic pitch diameter is 0.6604 in (16.774 mm) and basic minor diameter is 0.6424 in (16.317 mm). Tapped-hole figures on this page assume a class 2B thread; drill sizes for 50–85% engagement are in the tap drill table below.

Series: Unified Extra Fine (UNEF)
Designation: 11/16-24 UNEF
TPI: 24
Standard: ASME B1.1

Tap drill · 86.6% thread · cut tap

41/64

Drill Ø: 0.6406in
Drill Ø: 16.272mm

Assumes 75% thread engagement with a cut tap and a class 2B hole. That drill actually leaves 86.6% thread.

Basic Thread Dimensions for 11/16"-24 UNEF

Basic thread dimensions — 11/16"-24 UNEF
Property	Inch	Millimetre
Basic major diameter	0.6875	17.462
Threads per inch	24	—
Pitch	0.0417	1.058
Basic pitch diameter	0.6604	16.774
Basic minor diameter	0.6424	16.317
External thread root diameter	0.6379	16.203
Sharp V thread height (H)	0.0361	0.917

Threads per inch has no millimetre counterpart — metric threads are specified by pitch instead. Basic dimensions are the theoretical values before any tolerance class is applied.

Tap Drill Sizes for 11/16"-24 UNEF

Cut taps, from 50% to 85% thread engagement. The shop default is 75% — a 41/64 drill. Deeper engagement means more holding strength and more torque on the tap.

Tap drill sizes by thread engagement — 11/16"-24 UNEF, cut tap
Property	Target hole Ø		Nearest standard drill			Property
Thread %	in	mm	Drill	in	mm	Actual thread %
50%	0.6604	16.774	21/32	0.6563	16.669	57.7
60%	0.6550	16.637	21/32	0.6563	16.669	57.7
65%	0.6523	16.568	21/32	0.6563	16.669	57.7
70%	0.6496	16.500	21/32	0.6563	16.669	57.7
75%default	0.6469	16.431	41/64	0.6406	16.272	86.6
80%	0.6442	16.363	41/64	0.6406	16.272	86.6
85%	0.6415	16.294	41/64	0.6406	16.272	86.6

Target hole Ø is the theoretical hole for the stated engagement. The drill column is the nearest size in the standard number/letter/fractional/metric index, and actual thread % is what that real drill produces — the number that matters at the machine. Values are for cut taps. Tapped-hole figures assume a class 2B hole.

Thread Class Limits for 11/16"-24 UNEF

Manufacturing limits for classes 2B, 3B, 2A, 3A. A gauge reading outside these bands is a reject, not a judgement call.

External thread (bolt / screw) limits — 11/16"-24 UNEF
Property	Class 2A		Class 3A
Limit	in	mm	in	mm
Major Ø max	0.6863	17.432	0.6875	17.462
Major Ø min	0.6791	17.249	0.6803	17.280
Pitch Ø max	0.6592	16.744	0.6604	16.774
Pitch Ø min	0.6552	16.642	0.6574	16.698
Pitch Ø tolerance	0.0040	0.102	0.0030	0.076
Minor Ø max	0.6322	16.058	0.6334	16.088
Minor Ø min	0.6281	15.954	0.6303	16.010
Allowance	0.0012	0.030	0.0000	0.000

Internal thread (nut / tapped hole) limits — 11/16"-24 UNEF
Property	Class 2B		Class 3B
Limit	in	mm	in	mm
Major Ø max	0.6988	17.750	0.6975	17.716
Major Ø min	0.6875	17.462	0.6875	17.462
Pitch Ø max	0.6657	16.909	0.6644	16.876
Pitch Ø min	0.6604	16.774	0.6604	16.774
Pitch Ø tolerance	0.0053	0.135	0.0039	0.099
Minor Ø max	0.6521	16.563	0.6494	16.495
Minor Ø min	0.6424	16.317	0.6424	16.317
Allowance	0.0000	0.000	0.0000	0.000

Tensile Stress Area of 11/16"-24 UNEF

The effective cross-section used to size a 11/16"-24 UNEF fastener against a load. Multiply it by the material's allowable stress — the area itself carries no strength assumption.

Tensile stress area — 11/16"-24 UNEF
Property	in²	mm²
Tensile stress area	0.32868	212.05

The formula this value comes from is in the sources section below.

Sources and Method for 11/16"-24 UNEF

Basic dimensionscomputed

NBS Handbook H28 (1969) Part I §§6-7 (public domain, 17 U.S.C. 105); normative modern reference ASME B1.1; series membership: Series membership: threadlib UIS_thread.csv (BSD-3-Clause); cross-checked against NBS H28 (1969) Part I Table 2.21; clearance holes: ISO 273 (metric) and ASME B18.2.8 (inch) via FreeCAD FeatureHole.cpp (LGPL-2.1+), cross-checked against bd_warehouse clearance_hole_sizes.csv (Apache-2.0)

Verified against NBS H28 (1969) Part I, Table 2.21 (public domain); cross-checked against FreeCAD CAM thread tables (LGPL-2.1+) — 1064 checks passed at 0.0001 in

Computed from the standard's formulas, then checked against published tables.

Tap drill sizescomputed

Machinery's Handbook %-thread formula (geometry-derived); nearest-standard-drill-to-75% rule verified at 36/39 published chart rows in docs/research/data-sourcing.md §3.4

Verified against Wikipedia Unified Thread Standard, preferred cutting tap drill size columns (CC BY-SA 4.0) — 36/39 published UNC+UNF rows reproduced

Computed from the standard's formulas, then checked against published tables.

Class limitscomputed

NBS Handbook H28 (1969) Part I §§6-7 (public domain, 17 U.S.C. 105); normative modern reference ASME B1.1

Verified against NBS H28 (1969) Part I, Table 2.21 (public domain); cross-checked against FreeCAD CAM thread tables (LGPL-2.1+) — 1064 checks passed at 0.0001 in

Computed from the standard's formulas, then checked against published tables.

Formula

Tap drill hole diameter, inch threads

hole Ø  =  D − (%thread ÷ 100) × (1.29904 ÷ n)

  D = basic major diameter (in)
  n = threads per inch

1.29904 = 2 × 0.64952, twice the engaged thread height per side on the 60° Unified profile.

Actual thread engagement of the chosen drill

%thread  =  (D − drill Ø) × n ÷ 1.29904 × 100

The drill column rounds to a real drill; this is the engagement that drill actually leaves.

Tensile stress area, Unified inch threads

At  =  0.7854 × (D − 0.9743 ÷ n)²

ASME B1.1 / NBS H28 form. Reproduces the stored value exactly for this thread.

Assumptions

The headline tap drill assumes 75% thread engagement, the general shop default. Every other engagement from 50% to 85% is in the tap drill table — change the assumption and the number moves.
Tap drill figures are for cut taps. Drill diameters are nominal; a worn or run-out drill cuts oversize and reduces engagement further.
Tapped-hole figures assume a class 2B internal thread, the general-purpose fit.
Dataset scope: Le = 1D for UNC/UNF, 9P for UNEF — determined empirically against H28 Table 2.21, resolving data-sourcing.md open item 5. EXCLUDED: form (roll) tap drills, class 1A/1B limits, class 1AR allowances, constant-pitch UN series.

Data last verified

August 1, 2026

How this data is built and checked →

How to Cite This 11/16"-24 UNEF Reference

Citation

ShopMath. "11/16"-24 UNEF Thread — Dimensions, Tap Drill & Clearance." ShopMath, verified August 1, 2026, https://shopmath.org/threads/unef/11-16-24

BibTeX

@misc{shopmath-threads-unef-11-16-24,
  title        = {11/16"-24 UNEF Thread — Dimensions, Tap Drill & Clearance},
  author       = {{ShopMath}},
  year         = {2026},
  howpublished = {\url{https://shopmath.org/threads/unef/11-16-24}},
  note         = {Data verified 2026-08-01}
}

Permanent URL

https://shopmath.org/threads/unef/11-16-24

Common Questions About 11/16"-24 UNEF

What is the tap drill size for 11/16"-24 UNEF?: The tap drill for 11/16"-24 UNEF is 41/64 — 0.6406 in (16.272 mm). That leaves 86.6% thread engagement with a cut tap.
What is the pitch diameter of 11/16"-24 UNEF?: The basic pitch diameter of 11/16"-24 UNEF is 0.6604 in (16.774 mm). For a class 2B thread it runs 0.6604 in (16.774 mm) to 0.6657 in (16.909 mm).
What is the minor diameter of 11/16"-24 UNEF?: The basic minor diameter of 11/16"-24 UNEF is 0.6424 in (16.317 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.
What is the thread pitch of 11/16"-24 UNEF?: 11/16"-24 UNEF has 24 threads per inch, a pitch of 0.0417 in (1.058 mm).
What is the tensile stress area of 11/16"-24 UNEF?: The tensile stress area of 11/16"-24 UNEF is 0.32868 in² (212.05 mm²). Multiply it by the fastener material's allowable stress to get a load.

All Unified Extra Fine (UNEF) sizes · Every thread series