What is the tap drill size for 7/16"-20 UNF?

The tap drill for 7/16"-20 UNF is 25/64 — 0.3906 in (9.922 mm). That leaves 72.2% thread engagement with a cut tap.

What is the pitch diameter of 7/16"-20 UNF?

The basic pitch diameter of 7/16"-20 UNF is 0.4050 in (10.287 mm). For a class 2B thread it runs 0.4050 in (10.287 mm) to 0.4104 in (10.424 mm).

What is the minor diameter of 7/16"-20 UNF?

The basic minor diameter of 7/16"-20 UNF is 0.3834 in (9.738 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.

What is the thread pitch of 7/16"-20 UNF?

7/16"-20 UNF has 20 threads per inch, a pitch of 0.0500 in (1.270 mm).

What size clearance hole does a 7/16"-20 UNF fastener need?

close fit 7/16 (0.4528 in (11.501 mm)), normal fit 29/64 (0.4685 in (11.900 mm)), loose fit 15/32 (0.4843 in (12.301 mm)). The normal fit is the general-assembly default.

What is the tensile stress area of 7/16"-20 UNF?

The tensile stress area of 7/16"-20 UNF is 0.11872 in² (76.59 mm²). Multiply it by the fastener material's allowable stress to get a load.

Unified Fine (UNF) · 7/16-20 UNF

7/16"-20 UNF Thread — Dimensions, Tap Drill & Clearance

https://shopmath.org/threads/unf/7-16-20 · data verified August 1, 2026

The tap drill for 7/16"-20 UNF is 25/64 — 0.3906 in (9.922 mm) — which leaves 72.2% thread engagement with a cut tap. Basic pitch diameter is 0.4050 in (10.287 mm) and basic minor diameter is 0.3834 in (9.738 mm). Tapped-hole figures on this page assume a class 2B thread; drill sizes for 50–85% engagement are in the tap drill table below.

Series: Unified Fine (UNF)
Designation: 7/16-20 UNF
TPI: 20
Standard: ASME B1.1

Tap drill · 72.2% thread · cut tap

25/64

Drill Ø: 0.3906in
Drill Ø: 9.922mm
Clearance (normal): 29/64

Assumes 75% thread engagement with a cut tap and a class 2B hole. That drill actually leaves 72.2% thread.

Basic Thread Dimensions for 7/16"-20 UNF

Basic thread dimensions — 7/16"-20 UNF
Property	Inch	Millimetre
Basic major diameter	0.4375	11.113
Threads per inch	20	—
Pitch	0.0500	1.270
Basic pitch diameter	0.4050	10.287
Basic minor diameter	0.3834	9.738
External thread root diameter	0.3780	9.601
Sharp V thread height (H)	0.0433	1.100

Threads per inch has no millimetre counterpart — metric threads are specified by pitch instead. Basic dimensions are the theoretical values before any tolerance class is applied.

Tap Drill Sizes for 7/16"-20 UNF

Cut taps, from 50% to 85% thread engagement. The shop default is 75% — a 25/64 drill. Deeper engagement means more holding strength and more torque on the tap.

Tap drill sizes by thread engagement — 7/16"-20 UNF, cut tap
Property	Target hole Ø		Nearest standard drill			Property
Thread %	in	mm	Drill	in	mm	Actual thread %
50%	0.4050	10.287	Y	0.4040	10.262	51.6
60%	0.3985	10.122	X	0.3970	10.084	62.4
65%	0.3953	10.041	X	0.3970	10.084	62.4
70%	0.3920	9.957	25/64	0.3906	9.922	72.2
75%default	0.3888	9.876	25/64	0.3906	9.922	72.2
80%	0.3855	9.792	W	0.3860	9.804	79.3
85%	0.3823	9.710	W	0.3860	9.804	79.3

Target hole Ø is the theoretical hole for the stated engagement. The drill column is the nearest size in the standard number/letter/fractional/metric index, and actual thread % is what that real drill produces — the number that matters at the machine. Values are for cut taps. Tapped-hole figures assume a class 2B hole.

Clearance Hole Sizes for 7/16"-20 UNF

The through-hole a 7/16"-20 UNF fastener passes freely, not the tapped hole.

Clearance hole sizes — 7/16"-20 UNF
Property	Property	Hole Ø		Property
Fit	Drill	in	mm	Use
Close	7/16	0.4528	11.501	Located joints, dowelled assemblies
Normal	29/64	0.4685	11.900	General assembly — the default
Loose	15/32	0.4843	12.301	Slotted or adjustable joints, weldments

Clearance holes per ISO 273 (metric) and ASME B18.2.8 (inch). The drill column is the nearest standard drill at or above the specified hole diameter.

Thread Class Limits for 7/16"-20 UNF

Manufacturing limits for classes 2B, 3B, 2A, 3A. A gauge reading outside these bands is a reject, not a judgement call.

External thread (bolt / screw) limits — 7/16"-20 UNF
Property	Class 2A		Class 3A
Limit	in	mm	in	mm
Major Ø max	0.4362	11.079	0.4375	11.113
Major Ø min	0.4281	10.874	0.4294	10.907
Pitch Ø max	0.4038	10.257	0.4050	10.287
Pitch Ø min	0.3996	10.150	0.4019	10.208
Pitch Ø tolerance	0.0042	0.107	0.0031	0.079
Minor Ø max	0.3713	9.431	0.3725	9.461
Minor Ø min	0.3671	9.324	0.3694	9.383
Allowance	0.0013	0.033	0.0000	0.000

Internal thread (nut / tapped hole) limits — 7/16"-20 UNF
Property	Class 2B		Class 3B
Limit	in	mm	in	mm
Major Ø max	0.4501	11.432	0.4488	11.399
Major Ø min	0.4375	11.113	0.4375	11.113
Pitch Ø max	0.4104	10.424	0.4091	10.391
Pitch Ø min	0.4050	10.287	0.4050	10.287
Pitch Ø tolerance	0.0054	0.137	0.0041	0.104
Minor Ø max	0.3949	10.030	0.3916	9.947
Minor Ø min	0.3834	9.738	0.3834	9.738
Allowance	0.0000	0.000	0.0000	0.000

Tensile Stress Area of 7/16"-20 UNF

The effective cross-section used to size a 7/16"-20 UNF fastener against a load. Multiply it by the material's allowable stress — the area itself carries no strength assumption.

Tensile stress area — 7/16"-20 UNF
Property	in²	mm²
Tensile stress area	0.11872	76.59

The formula this value comes from is in the sources section below.

Other Thread Pitches in the Same Size as 7/16"-20 UNF

A 7/16 fastener is not always 7/16"-20 UNF. These are the other standard pitches cut on the same nominal size.

Other standard pitches at nominal size 7/16
Thread	Series	Pitch	Tap drill
7/16"-28 UNEF	Unified Extra Fine (UNEF)	28 TPI	Y
7/16"-14 UNC	Unified Coarse (UNC)	14 TPI	U

Sources and Method for 7/16"-20 UNF

Basic dimensionscomputed

NBS Handbook H28 (1969) Part I §§6-7 (public domain, 17 U.S.C. 105); normative modern reference ASME B1.1; series membership: Series membership: threadlib UIS_thread.csv (BSD-3-Clause); cross-checked against NBS H28 (1969) Part I Table 2.21; clearance holes: ISO 273 (metric) and ASME B18.2.8 (inch) via FreeCAD FeatureHole.cpp (LGPL-2.1+), cross-checked against bd_warehouse clearance_hole_sizes.csv (Apache-2.0)

Verified against NBS H28 (1969) Part I, Table 2.21 (public domain); cross-checked against FreeCAD CAM thread tables (LGPL-2.1+) — 1064 checks passed at 0.0001 in

Computed from the standard's formulas, then checked against published tables.

Tap drill sizescomputed

Machinery's Handbook %-thread formula (geometry-derived); nearest-standard-drill-to-75% rule verified at 36/39 published chart rows in docs/research/data-sourcing.md §3.4

Verified against Wikipedia Unified Thread Standard, preferred cutting tap drill size columns (CC BY-SA 4.0) — 36/39 published UNC+UNF rows reproduced

Computed from the standard's formulas, then checked against published tables.

Class limitscomputed

NBS Handbook H28 (1969) Part I §§6-7 (public domain, 17 U.S.C. 105); normative modern reference ASME B1.1

Verified against NBS H28 (1969) Part I, Table 2.21 (public domain); cross-checked against FreeCAD CAM thread tables (LGPL-2.1+) — 1064 checks passed at 0.0001 in

Computed from the standard's formulas, then checked against published tables.

Formula

Tap drill hole diameter, inch threads

hole Ø  =  D − (%thread ÷ 100) × (1.29904 ÷ n)

  D = basic major diameter (in)
  n = threads per inch

1.29904 = 2 × 0.64952, twice the engaged thread height per side on the 60° Unified profile.

Actual thread engagement of the chosen drill

%thread  =  (D − drill Ø) × n ÷ 1.29904 × 100

The drill column rounds to a real drill; this is the engagement that drill actually leaves.

Tensile stress area, Unified inch threads

At  =  0.7854 × (D − 0.9743 ÷ n)²

ASME B1.1 / NBS H28 form. Reproduces the stored value exactly for this thread.

Assumptions

The headline tap drill assumes 75% thread engagement, the general shop default. Every other engagement from 50% to 85% is in the tap drill table — change the assumption and the number moves.
Tap drill figures are for cut taps. Drill diameters are nominal; a worn or run-out drill cuts oversize and reduces engagement further.
Tapped-hole figures assume a class 2B internal thread, the general-purpose fit.
Dataset scope: Le = 1D for UNC/UNF, 9P for UNEF — determined empirically against H28 Table 2.21, resolving data-sourcing.md open item 5. EXCLUDED: form (roll) tap drills, class 1A/1B limits, class 1AR allowances, constant-pitch UN series.

Data last verified

August 1, 2026

How this data is built and checked →

How to Cite This 7/16"-20 UNF Reference

Citation

ShopMath. "7/16"-20 UNF Thread — Dimensions, Tap Drill & Clearance." ShopMath, verified August 1, 2026, https://shopmath.org/threads/unf/7-16-20

BibTeX

@misc{shopmath-threads-unf-7-16-20,
  title        = {7/16"-20 UNF Thread — Dimensions, Tap Drill & Clearance},
  author       = {{ShopMath}},
  year         = {2026},
  howpublished = {\url{https://shopmath.org/threads/unf/7-16-20}},
  note         = {Data verified 2026-08-01}
}

Permanent URL

https://shopmath.org/threads/unf/7-16-20

Common Questions About 7/16"-20 UNF

What is the tap drill size for 7/16"-20 UNF?: The tap drill for 7/16"-20 UNF is 25/64 — 0.3906 in (9.922 mm). That leaves 72.2% thread engagement with a cut tap.
What is the pitch diameter of 7/16"-20 UNF?: The basic pitch diameter of 7/16"-20 UNF is 0.4050 in (10.287 mm). For a class 2B thread it runs 0.4050 in (10.287 mm) to 0.4104 in (10.424 mm).
What is the minor diameter of 7/16"-20 UNF?: The basic minor diameter of 7/16"-20 UNF is 0.3834 in (9.738 mm). That is the theoretical root of the internal thread, not the drilled hole size — see the tap drill table for the hole to drill.
What is the thread pitch of 7/16"-20 UNF?: 7/16"-20 UNF has 20 threads per inch, a pitch of 0.0500 in (1.270 mm).
What size clearance hole does a 7/16"-20 UNF fastener need?: close fit 7/16 (0.4528 in (11.501 mm)), normal fit 29/64 (0.4685 in (11.900 mm)), loose fit 15/32 (0.4843 in (12.301 mm)). The normal fit is the general-assembly default.
What is the tensile stress area of 7/16"-20 UNF?: The tensile stress area of 7/16"-20 UNF is 0.11872 in² (76.59 mm²). Multiply it by the fastener material's allowable stress to get a load.

All Unified Fine (UNF) sizes · Every thread series