What size is a #7 drill bit?

A #7 drill bit is 0.2010 in in diameter, which is 5.105 mm.

What thread does a #7 drill bit tap?

A #7 drill bit is the tap drill for 1/4"-20 UNC at 75% requested thread engagement, where it leaves 75.4% thread with a cut tap.

What is the metric equivalent of a #7 drill bit?

The closest metric drill to a #7 drill bit (5.105 mm) is 5.1 mm, which is 5.100 mm — 0.0002 in smaller.

What fraction is a #7 drill bit closest to?

A #7 drill bit (0.2010 in) sits closest to the 13/64" fractional drill at 0.2031 in, a difference of 0.0021 in.

Number drill · #7

#7 Drill Bit Size — Decimal Inch, Millimetre and Tap Sizes

https://shopmath.org/drills/number/7 · data verified August 1, 2026

A #7 drill bit is 0.2010 in (5.105 mm) in diameter. It is the tap drill for 1/4"-20 UNC at 75% thread engagement with a cut tap, where it leaves 75.4% thread. The nearest fractional size is 13/64" at 0.2031 in. Diameters are nominal.

Series: Number
Designation: #7
Inch: 0.2010
mm: 5.105
Standard: ANSI/ASME B94.11M

Number Drill · #7 · nominal diameter

0.2010 in

Millimetre: 5.105mm
Taps: 1/4"-20 UNC

Nominal diameter. As a tap drill it leaves 75.4% thread in 1/4"-20 UNC with a cut tap.

#7 Drill Bit Size in Inches and Millimetres

The nominal diameter of a #7 drill bit. Drill sizes are nominal — a worn drill, run-out or a soft material that closes in behind the cut all move the finished hole.

#7 drill bit — decimal inch and millimetre diameter
Property	Value
Diameter, decimal inch	0.2010 in
Diameter, millimetre	5.105 mm
Cross-sectional area	0.03173 in²

1 in = 25.4 mm exactly, so the two columns are the same value in different units, not two measurements.

Threads a #7 Drill Bit Taps

Every thread in this reference whose tap drill is the #7 drill bit, and the thread engagement it leaves. The engagement asked for and the engagement the drill actually produces are different numbers — that gap is why both columns are here.

Threads tapped with a #7 drill bit, by thread engagement
Thread	Series	Thread % asked for	Thread % this drill leaves
1/4"-20 UNC	Unified Coarse (UNC)	75%default	75.4

Values are for cut taps. Rows marked default are the shop-default engagement for that thread.

#7 Drill Bit Equivalents in Every Other Drill Series

The closest size to the #7 drill bit in each of the other three indexes, with the difference in inches. None of them is the same drill — check the difference before substituting one into a tapped hole.

Nearest number, letter, fractional and metric equivalents to a #7 drill bit
Property	Property	Diameter		Property
Drill	Series	in	mm	Difference, in
A	Letter	0.2340	5.944	+0.0330
13/64"	Fractional	0.2031	5.159	+0.0021
5.1 mm	Metric	0.2008	5.100	−0.0002

A positive difference means the equivalent drill is larger, which leaves less thread in a tapped hole. Sizes without a link are stored for the nearest-drill calculation but do not carry their own page.

Drill Sizes Either Side of the #7 Drill Bit

Ordered by diameter across all four indexes, so the next size up may be a letter, a fraction or a metric drill rather than the next one in this series.

Standard drill sizes adjacent to a #7 drill bit, by diameter
Property	Property	Diameter
Drill	Series	in	mm
#8	Number	0.1990	5.055
5.1 mm	Metric	0.2008	5.100
#7	Number	0.2010	5.105
13/64"	Fractional	0.2031	5.159
#6	Number	0.2040	5.182

Sources and Method for the #7 Drill Bit Size

Drill diametercompiled

Number/letter: bd_warehouse drill_sizes.csv (Apache-2.0) cross-checked against Wikipedia Drill bit sizes (CC BY-SA 4.0). Fractional: computed 1/64 in steps per ANSI B94.11M. Metric: computed BS 328 increment pattern.

Verified against Wikipedia Drill bit sizes (CC BY-SA 4.0); 31/31 checks passed

Compiled from independent public sources that agree cell-for-cell.

Tap drill usagecomputed+compiled

bd_warehouse drill_sizes.csv (Apache-2.0) + Wikipedia Drill bit sizes (CC BY-SA 4.0); fractional and metric computed from ANSI B94.11M / BS 328 increment patterns

Verified against drills: 31 checks passed across 1 harness(es)

Part computed from the standard's formulas, part compiled from agreeing public sources.

Assumptions

Diameters are nominal. Drill manufacturing tolerance, wear and run-out all cut oversize, and every one of those moves a tapped hole toward less thread than the table says.
Tap drill usage assumes cut taps. 1/4"-20 UNC at 75% requested engagement is what this drill is normally bought for.
Dataset scope: Number sizes #61-#80 are stored but tagged demandTier 'extended' — query-space-map.md Appendix A found the tail thinning in the 60s. Sizes below #80 and metric sizes above 25.0 mm excluded.

Data last verified

August 1, 2026

How this data is built and checked →

How to Cite This #7 Drill Bit Reference

Citation

ShopMath. "#7 Drill Bit Size — Decimal Inch, Millimetre and Tap Sizes." ShopMath, verified August 1, 2026, https://shopmath.org/drills/number/7

BibTeX

@misc{shopmath-drills-number-7,
  title        = {#7 Drill Bit Size — Decimal Inch, Millimetre and Tap Sizes},
  author       = {{ShopMath}},
  year         = {2026},
  howpublished = {\url{https://shopmath.org/drills/number/7}},
  note         = {Data verified 2026-08-01}
}

Permanent URL

https://shopmath.org/drills/number/7

Common Questions About the #7 Drill Bit

What size is a #7 drill bit?: A #7 drill bit is 0.2010 in in diameter, which is 5.105 mm.
What thread does a #7 drill bit tap?: A #7 drill bit is the tap drill for 1/4"-20 UNC at 75% requested thread engagement, where it leaves 75.4% thread with a cut tap.
What is the metric equivalent of a #7 drill bit?: The closest metric drill to a #7 drill bit (5.105 mm) is 5.1 mm, which is 5.100 mm — 0.0002 in smaller.
What fraction is a #7 drill bit closest to?: A #7 drill bit (0.2010 in) sits closest to the 13/64" fractional drill at 0.2031 in, a difference of 0.0021 in.

All number drill sizes · Complete drill size chart · Every drill series